济南模型公司
  • 济南市市中区
  • 经十西路6288号1号楼101室
  • 电话:0531-55504101
  • 网站:http://www.jnsymx.com
  • 手机:18660800958 13869134430
新闻中心当前位置:首页-新闻中心
    模型建造对锡箔纸和有机玻璃这两种材料的应用
    2019-4-2 11:57:46 来源:http://www.jnsymx.com
    潍坊模型公司在产品制作的时候,有时会用到的锡箔纸和有机玻璃这两种材料,下面我们就一起看看他们的用处和加工注意事项吧!
    Weifang Model Company sometimes uses tinfoil and organic glass when making products. Let's take a look at their usefulness and processing precautions together.
    (l)金属、不锈钢柱:将银色或金黄色的铝箔纸以一个细铁针卷成一个小圆筒,再将其展平,裁下一定的长度后,重新卷成空心筒,按设计的柱子粗细调整好,并粘接好接头处。这样就加工好一个金属饰面的柱子。
    (l) Metal and stainless steel pillars: roll silver or gold foil paper into a small cylinder with a fine iron needle, flatten it, cut a certain length, reel it into a hollow cylinder, adjust according to the thickness of the designed pillars, and bond the joint. In this way, a metal-trimmed pillar is processed.
    (2)馆金字样的加工:将率按一定的大小和字体书写在硫酸纸上,再将金箔正面向上放在硫酸纸上,然后同时将重叠的两张纸一起翻过来,并在下面放几张软纸整好。用圆珠笔在透过来的字迹上重新用力描写,将字迹印在金箔上,再将金箔上的字迹剪下,即加工成馆金字。
    (2) Processing of the gold letters in the library: Write the rate on the sulfuric acid paper according to certain size and font, then put the gold foil on the sulfuric acid paper frontally upward, then turn over the overlapping two pieces of paper together, and put a few pieces of soft paper underneath. The ballpoint pen is used to re-describe the transmitted handwriting, and the handwriting is printed on the gold foil. Then the handwriting on the gold foil is cut off, that is to say, it is processed into the library gold characters.
    (3)作铝合金门窗:将银色箔纸压平后粘在白板纸上,待白胶干后,用大头针在箔纸正面面上门窗捱,然后用手术刀刻画成铝合金门窗框,再将其粘在深颜色作为玻璃的材料上,即加工成铝合金门富了。

    (3) Aluminum alloy doors and windows: the silver foil paper is pressed flat and glued to the white board paper. After the white glue is dried, the large needle is used to endure the doors and windows on the front of the foil paper. Then the aluminium alloy doors and windows frame is depicted with a scalpel, and then glued to the deep color glass material, that is, the aluminium alloy doors and windows are rich.

    潍坊模型公司产品

    有机玻璃的加工:
    Processing of plexiglass:
    (1)角尖头木刻刀,在茶色或蓝色有机玻璃上刻画窗子,然后在条痕上涂白色水粉,再将有机玻璃擦干净,就加工成大玻璃面或地面。
    (1) Angle-pointed woodcut knife, painted windows on brown or blue plexiglass, then coated with white water powder on the strips, and then wiped the plexiglass clean, then processed into large glass surface or ground.
    (2)用尖头木刻刀将白色或深灰色3-4毫米厚的有机玻璃,先以60o斜向按一定的间距刻下半透的刀痕,再以90”垂直割断,使其断面呈锯齿形,这样就加工成不同比例的台阶踏步。
    (2) The white or dark gray 3-4 mm thick plexiglass is carved with a sharp woodcut knife. The semi-penetrating cutter marks are carved at a certain distance in an oblique direction of 60o, and then cut vertically with 90"to make its cross section serrated, so that it can be processed into step steps of different proportions.
    (3)将透明塑料板在电热丝加热下,弯折成弧形拱或各种角度,就加工成天窗、均窗和透光风雨篷。
    (3) By bending transparent plastic sheets into arc arches or various angles under the heating of electric heating wires, they are processed into skylights, even windows and transparent wind awnings.
    今天的精彩内容就给大家介绍到这里了,如果您有对沙盘模型、房地产模型等产品的需求,欢迎咨询我们官网的客服人员:潍坊模型公司http://www.jnsymx.com
    Today's wonderful content will be introduced here. If you have the demand for sand table model, real estate model and other products, please consult our customer service staff: Weifang Model Company http://www.jnsymx.com
    版权所有:济南市槐荫区视野模型设计制作中心 Copyright @ 2011-2012 电话:18660800958  传真:0531-55504101 鲁ICP备11014722号 地址:济南市市中区经十西路6288号1号楼101室 
    网址:http://www.jnsymx.com