济南模型公司
  • 济南市市中区
  • 经十西路6288号1号楼101室
  • 电话:0531-55504101
  • 网站:http://www.jnsymx.com
  • 手机:18660800958 13869134430
新闻中心当前位置:首页-新闻中心
    建筑模型制作是怎样安排布局的?
    2017-10-20 16:05:06 来源:http://www.jnsymx.com
    建筑模型的制作很多是未建设好的规划建筑,制作过程中不仅需要较高的制作技巧,其中还包含了很多巧妙布局,使我们的沙盘模型既逼真又不失美观。那么建筑模型制作怎样合理安排布局呢?
    The building model is a lot of good planning and architectural construction, the production process requires not only high production skills, which also contains a lot of clever layout, make our sandbox model realistic and yet beautiful. So, how to arrange the layout of the building model?
    首先,要明确建筑模型实际要表现的用地的范围,用地红线是制定方案的核心,围绕着这个核心把周边坐标性的元素适当表现出来,如道路、桥梁、标志性建筑、河渠等。以这些为向导,客户就对建筑模型的位置和关系有了比较清晰的认识。
    First of all, to clear the building model to the performance of the actual land area, land planning is the core, around the core of the surrounding coordinate proper elements displayed, such as roads, bridges, canals, and other landmarks. With these as the guide, customers have a clear understanding of the location and relationship of the building model.
    模型制作
    Model making
    其次是对实际要表现的建筑模型景物,在进行布局时要考虑以下几个方面。
    Secondly, we should consider the following aspects in the layout of the building model.
    1、要以主景为主要表现对象,切忌喧宾夺主。要合理把握精与粗、虚与实的合理关系。整个建筑模型的中心或是重心部分应该占据主要的视角。
    1, to the main performance as the main object, avoid distracting. Reasonable relationship should reasonably grasp the fine and coarse, and the. The center of the building model or the center of gravity should occupy the main visual angle.
    2、对衬托和附加元素可以做适当的夸张和省略处理。这一部分的商业陷阱较多,也是商业策划中有价值的部分。
    2, to the background and additional elements can do appropriate exaggeration and ellipsis processing. This part of the business trap is more, but also the most valuable part of business planning.
    3、无论如何处理,都必须基本符合视觉规划技术逻辑和美学构图的要求,并实事求是地写明建筑模型的示意关系,具体以政府有关部门审定的文件为准。总之,把握这个度是关键,有时坦诚更能获得理解。
    3, in any case, must comply with the basic visual programming technique and aesthetic logic composition requirements, and to indicate the relationship of realistic architectural model, the relevant departments in the government's specific approval document shall prevail. In short, it is the key to grasp this degree, and sometimes frankness is better understood.
    模型制作中的木板拼接方法有哪些

    What are the methods of wood splicing in model making?

    聊城模型制作公司

    在制作常规沙盘模型时,板材宽度或者长度不能满足模型制作尺寸的情况。因为有的沙盘模型比例比较大,需要的板材宽度也较大,这时候我们就要通过拼接来完成。我们来介绍一下模型制作中的木板拼接方法。木板材拼接一般是选择一些纹理相近、色彩一直的板材进行拼接,方法有如下几种。
    When making the conventional sand table model, the width or length of the plate can not meet the size of the model. Because some sand table model ratio is large, the width of the plate is also large, at this time we have to complete the stitching. Let's introduce the wood mosaic method in model making. Wood plate splicing is usually to choose some texture similar, color has been the plate splicing, methods are as follows.
    1、对接法 对接法是一种板材拼接常用方法。它首先要将拼接木板的接口进行打磨处理,使其缝隙严密,然后刷上乳胶进行对接。对接时略加力,将拼接板进行搓挤,使其接口内的夹胶溢出接缝,然后将其放置于通风处干燥。
    1, butt joint method is a common method of plate splicing. Firstly, the interface of the spliced wood board is polished, so that the gap is tight, and then the latex is brushed to butt joint. Butt slightly afterburner, splicing plate rolling, the interface of the laminated seams and then the overflow, placed in ventilated dry place.
    模型制作
    Model making
    2、搭接法 搭接法主要用于厚木板材的拼接。在拼接时,首先要把拼接板接口切成字母口,然后在接口处刷上乳胶并进行挤压,将多余的胶液挤出,经认定接缝严密后,放置于通风处干燥。
    2, lap lap method is mainly used to splice plate construction. In the process of splicing, the interface of the splicing plate should be cut into the mouth of the letter first, then the latex at the interface is extruded and extruded, and the excess glue is squeezed out. After the seam is confirmed tight, it is placed in the ventilation place and dried.
    3、剖面拼接法 斜面拼接法主要用于薄木板的拼接。拼接时先用细木工刨将板材拼接口泡成斜面,斜面大小视其板材厚度而定,板材越薄,斜面则应越大。反之,板材越厚,斜面越小。接口刨好后,便可以刷胶、拼接。拼接后检查是否有错缝现象,若粘接无误,将其放置于通风处干燥。
    3. The method of profile stitching and bevel jointing is mainly used for the stitching of thin wood boards. In the process of splicing, the interface of the plate is first made into a slope with a carpenter's plane, and the size of the inclined plane is determined by the thickness of the plate, and the thinner the plate, the larger the incline. On the contrary, the thicker the plate, the smaller the slope. After the interface is planed, the glue can be brushed and spliced. After stitching, check whether there is a seam, if the bonding error, placed in the ventilation drying.
    作为模型制作公司,我们精心设计制作的每一件沙盘模型,都希望能够得到甲方和众人的认可,随着现代科技的发展,模型材料和制作工具更加多样和便捷,越来越多的设计作品采用沙盘模型形式来表现设计意图,具有广阔的市场前景和商业价值。
    As a model of production company, we carefully design each piece of sand table model made by Party A and hope to get everyone's approval, along with the development of modern science and technology, materials and tools for making model more diverse and convenient, the design work is more and more used in the form of sand table model performance design intent, and has broad market prospects and business value.
    以上文章来源于聊城模型公司http://www.jnsymx.com/
    版权所有:济南市槐荫区视野模型设计制作中心 Copyright @ 2011-2012 电话:18660800958  传真:0531-55504101 鲁ICP备11014722号 地址:济南市市中区经十西路6288号1号楼101室 
    网址:http://www.jnsymx.com