济南模型公司
  • 济南市市中区
  • 经十西路6288号1号楼101室
  • 电话:0531-55504101
  • 网站:http://www.jnsymx.com
  • 手机:18660800958 13869134430
新闻中心当前位置:首页-新闻中心
    济南楼盘模型的制作的七种材料
    2017-7-6 15:51:58 来源:http://www.jnsymx.com
    一、确定济南模型公司比例
    First, determine the proportion of Ji'nan model companies
    首先确定沙盘模型制作的总体方针和比例。城市规划、住宅区域规划等大范围的沙盘模型,比例一般为1:3000—1:5000;房地产楼盘等建筑模型的比例常为1:200—1:50;住宅模型,如果建筑物较小,采用1:50左右的比例就可以了。比例确定后,先做出建筑用的场地模型,清楚地形高差,景观印象等。
    First, determine the general policy and proportion of sand table model making. Sand table model of city planning, residential district planning in large scale, the proportion is 1:3000 - 1:5000; real estate building model proportion often 1:200 - 1:50; residential model, if the building is small, the ratio of about 1:50 can be. After the proportion is determined, the site model of the building is made first, and the elevation difference, landscape impression and so on are clearly defined.
    二、制作模型底座
    Two. Make model base
    比例确定后再做模型,先做模型底座与基地。如果建筑场地平坦,制作模型也简单。若场地高低不平,则依测量方法的不同,济南模型公司在模型的制作方法也有相应的区别。尤其是针对复杂地形和城市规划等大场地时,常常是先将地形模型事先做成,一边看着模型一边进行方案设计的情况较多。
    After the proportion is determined, the model is made, and the model base and base are made first. If the construction site is flat, the model is simple. If the site is uneven, according to the different measurement methods, the Ji'nan model company in the model making methods are also different. Especially for complex terrain and city planning a large, often is the first terrain model made in advance, while looking at the side of the model design more.
    三、用卡纸做模型
    Three, use cardboard model
    卡纸是常用模型材料,可以根据需要选择不同的卡纸,如:白卡,灰卡,色卡。
    The cardboard is a commonly used model material, can choose a different card, according to the needs of such as: white card, gray card, color card.
    四、用木板做模型
    Four. Make models out of planks
    运用轻木料木材的柔软而粗糙的才质质感及加工方便的特点,能做出多种种不同的表现效果。在切割薄而细的软木材坂料时,尽量使用薄形刀具,切割细小的软木时,可以使用安全刀片的刃口精心切下,切割范围很小时,应在木材下面帖上一层赛路硌透明纸带,这样可以增加其强度,不影响切割。
    The use of light wood, wood soft and rough quality, texture and processing convenience features, can make a variety of different performance. In the soft wood cutting of thin and fine Osaka, try to use thin cutter, cut the small cork, you can use the safety blade carefully cut, the cutting range is very small, should be in the wood below a layer of transparent Ge post synthesis tape, which can increase the strength, does not affect the cutting.
    五、用泡沫苯乙烯纸做模型
    Five. Use foam styrene paper as a model
    这种材料适合做一些草模和研究模型,非常便于加工。
    This material is suitable for making some straw models and research models, and is very easy to process.
    六、用塑料板做模型
    Six. Make models out of plastic sheets
    这种材料模型公司用的多,非常正式的模型才会用,加工起来很麻烦。
    This material model, the company used more, a very formal model will be used, processing is very troublesome.
    七、用有机玻璃做模型
    Seven. Make model with plexiglass
    由于这种材料很难切割,要用专用的刀才能切开,材料很透明,通常用来做外表面,方便看到内部空间。另外,有机玻璃模型也可用来做一些研究性模型。
    Since this material is difficult to cut, a special knife can be used to cut it. The material is very transparent and is usually used as an outer surface to facilitate internal space. In addition, plexiglass models can also be used to do research models.
    版权所有:济南市槐荫区视野模型设计制作中心 Copyright @ 2011-2012 电话:18660800958  传真:0531-55504101 鲁ICP备11014722号 地址:济南市市中区经十西路6288号1号楼101室 
    网址:http://www.jnsymx.com